source: arduino-1-6-7/trunk/fuentes/arduino-ide-amd64/hardware/arduino/avr/programmers.txt @ 4837

Last change on this file since 4837 was 4837, checked in by daduve, 3 years ago

Adding new version

File size: 3.3 KB
Line 
1avrisp.name=AVR ISP
2avrisp.communication=serial
3avrisp.protocol=stk500v1
4avrisp.program.protocol=stk500v1
5avrisp.program.tool=avrdude
6avrisp.program.extra_params=-P{serial.port}
7
8avrispmkii.name=AVRISP mkII
9avrispmkii.communication=usb
10avrispmkii.protocol=stk500v2
11avrispmkii.program.protocol=stk500v2
12avrispmkii.program.tool=avrdude
13avrispmkii.program.extra_params=-Pusb
14
15usbtinyisp.name=USBtinyISP
16usbtinyisp.protocol=usbtiny
17usbtinyisp.program.tool=avrdude
18usbtinyisp.program.extra_params=
19
20arduinoisp.name=ArduinoISP
21arduinoisp.protocol=arduinoisp
22arduinoisp.program.tool=avrdude
23arduinoisp.program.extra_params=
24
25arduinoisporg.name=ArduinoISP.org
26arduinoisporg.protocol=arduinoisporg
27arduinoisporg.program.tool=avrdude
28arduinoisporg.program.extra_params=
29
30usbasp.name=USBasp
31usbasp.communication=usb
32usbasp.protocol=usbasp
33usbasp.program.protocol=usbasp
34usbasp.program.tool=avrdude
35usbasp.program.extra_params=-Pusb
36
37parallel.name=Parallel Programmer
38parallel.protocol=dapa
39parallel.force=true
40# parallel.delay=200
41parallel.program.tool=avrdude
42parallel.program.extra_params=-F
43
44arduinoasisp.name=Arduino as ISP
45arduinoasisp.communication=serial
46arduinoasisp.protocol=stk500v1
47arduinoasisp.speed=19200
48arduinoasisp.program.protocol=stk500v1
49arduinoasisp.program.speed=19200
50arduinoasisp.program.tool=avrdude
51arduinoasisp.program.extra_params=-P{serial.port} -b{program.speed}
52
53usbGemma.name=Arduino Gemma
54usbGemma.protocol=arduinogemma
55usbGemma.program.tool=avrdude
56usbGemma.program.extra_params=
57usbGemma.config.path={runtime.platform.path}/bootloaders/gemma/avrdude.conf
58
59## Notes about Dangerous Prototypes Bus Pirate as ISP
60## Bus Pirate V3 need Firmware v5.10 or later
61## Bus Pirate V4 need Firmware v6.3-r2151 or later
62## Could happen that BP does not have enough current to power an Arduino board
63## through the ICSP connector. In this case disconnect the +Vcc from ICSP connector
64## and power Arduino board in the normal way.
65buspirate.name=BusPirate as ISP
66buspirate.communication=serial
67buspirate.protocol=buspirate
68buspirate.program.protocol=buspirate
69buspirate.program.tool=avrdude
70buspirate.program.extra_params=-P{serial.port}
71
72# STK500 firmware version v1 and v2 use different serial protocols.
73# Using the 'stk500' protocol tells avrdude to try and autodetect the
74# firmware version. If this leads to problems, we might need to add
75# stk500v1 and stk500v2 entries to allow explicitely selecting the
76# firmware version.
77stk500.name=Atmel STK500 development board
78stk500.communication=serial
79stk500.protocol=stk500
80stk500.program.protocol=stk500
81stk500.program.tool=avrdude
82stk500.program.extra_params=-P{serial.port}
83
84jtag3isp.name=Atmel JTAGICE3 (ISP mode)
85jtag3isp.communication=usb
86jtag3isp.protocol=jtag3isp
87jtag3isp.program.protocol=jtag3isp
88jtag3isp.program.tool=avrdude
89jtag3isp.program.extra_params=
90
91jtag3.name=Atmel JTAGICE3 (JTAG mode)
92jtag3.communication=usb
93jtag3.protocol=jtag3
94jtag3.program.protocol=jtag3
95jtag3.program.tool=avrdude
96# Set a bitclock of 0.1us (the fastest supported value). This should
97# work regardless of the crystal used, since JTAG doesn't use the MCU
98# clock but dictates its own clock.
99jtag3.program.extra_params=-B0.1
100
101atmel_ice.name=Atmel-ICE (AVR)
102atmel_ice.communication=usb
103atmel_ice.protocol=atmelice_isp
104atmel_ice.program.protocol=atmelice_isp
105atmel_ice.program.tool=avrdude
106atmel_ice.program.extra_params=-Pusb
Note: See TracBrowser for help on using the repository browser.